Swivel Chair Seat Post Bushing

This swivel post bushing fits a 1" round post and fits into a 1 5/8" round opening; overall height is 4 1/8". Sold individually. See Description and tabs below.

SKU: 30-922
  • Buy 4 for $7.20 each and save 10%
  • Buy 10 for $6.80 each and save 15%
  • Buy 50 for $6.40 each and save 20%
  • Buy 100 for $6.00 each and save 25%

This swivel post bushing fits a 1" round post and fits into a 1 5/8" round opening; overall height is 4 1/8". US standard size, not metric. The vertical flanges on this bushing make it more durable than other bushings with ring-type flanges. Black only. Click on additional part views to help confirm if this is the item you need. 

FIXES: When a swivel rocker seat wobbles, it needs a new swivel chair seat post bushing. 

Sold individually. No minimum quantity required; larger quantities are eligible for volume discounts as shown above when applied to the same item, sku and color on the same order.

  1. didn't fit Review by Paulmc

    I didn't read the measurements and thought one size fits all but not correct. Be sure to measure your tube that it fits in and the shaft.... (Posted on 7/20/2018)

  2. Tight Fit but worked well Review by jets4474

    Parts came as advertised. Fixed terrible squeaking notice and chairs swivel much easier. Fit was tighter than original part but was able to drive it into chair with rubber mallet. One part came slightly damaged but did not interfere with function. (Posted on 7/15/2018)

  3. did not fit Review by Bob

    did not fit, was too big OD, shaved some off OD, but the 1" ID was too small and could not shave some off because wall was too thin. (Posted on 7/10/2018)

  4. Too Tight, but worked Review by Gman5340

    It looked like it was too big to even get started going in. But I shaved off some of it then pounded it hard. Now it's snug and works great. (Posted on 6/26/2018)

  5. Its what I needed Review by pdm

    Exact replacement for the bushing on my 2007 Brown Jordan swivel rockers. It was
    a very tight fit however and heavy pounding was needed to drive it into the base. (Posted on 6/4/2018)

  6. Did not fit Review by Gil Dresback

    Did not fit and was dissapointed to hear there were no other sizes available on a chair that was only 3 years old...and then actual manufacturer no longer made them even though a five year warranty (Posted on 5/31/2018)

  7. Excellent replacement bushing Review by MJC

    Fast Shipping.Bushing as described.Very Tight fit for my Tropitone swivel rocker;required some heavy pounding with rubber mallet.Works great!Thanks (Posted on 3/29/2018)

  8. Product OK Review by Filet

    The bushing appeared to be the correct one but for what ever reason, it doesn't fit my chairs.
    (Posted on 3/2/2018)

  9. Perfect Fit Review by TK

    Perfect fit for my vintage Winston Ultimate High Back Swivel Tilt Chairs! I was careful when taking measurements and got the best results by removing the pedestal and using calipers. Some firm taps with a rubber mallet were needed to install them. Chairs work like new again! (Posted on 12/3/2017)

  10. Excellent Review by JG

    The fit was a little tight for our Tropitone swivel rocker. Just used a bigger hammer! Very satisfied. (Posted on 11/9/2017)

  11. Perfect fit Review by tedsone

    I have some old Winston swivel rockers that I got from my parents. I have been looking for this part for some time and this was the exact one I needed. My chairs are now restored like new. (Posted on 11/3/2017)

  12. Very good. Review by Bushing

    Fit perfectly. (Posted on 10/24/2017)

  13. To small Review by Nana

    I received my order in a timely matter. The chair bushing was good quality but they was to small for my chairs. (Posted on 8/16/2017)

  14. not bad, but.. Review by Bob W.

    The sleeve was a bit too wide to fit easily into my chairs. I tried pounding them in, but no luck. I'm sure that with a little filing or sanding they will work fine. (Posted on 7/10/2017)

  15. Didn't fit Review by Swivel

    Doesn't have a lip on the top and the diameter is to small. Falls throw the shaft.
    Can't say the product is bad, it just doesn't fit our swivel. (Posted on 7/6/2017)

  16. Excellent Review by Joe

    Part fit perfectly
    (Posted on 5/22/2017)

  17. hard plastic bushing (styrene) Review by growlind

    This part appears to be a styrene type plastic . should last years with very little modular deflection in normal use. (Posted on 7/13/2016)

  18. swivel chair seat post bushing Review by jerzy joe

    I am sure this is the part I need (Posted on 7/9/2015)

Write Your Own Review

You're reviewing: Swivel Chair Seat Post Bushing

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars

This Swivel Chair Seat Post Bushing is normally in stock and available to ship in 1-3 business days after receipt of payment.

Times indicated under Estimate Shipping & Tax on the cart page are the carriers’ estimated time of delivery after shipment; estimated time of delivery counts only the days the carrier delivers and does not include holidays or the day the package is shipped.

• United States Postal Service (USPS) First Class Mail transit times are determined by USPS.
• USPS Priority Mail 2-3 day service may take longer than 2-3 days in some instances.
• USPS Priority Mail International 6-10 day service may take longer in some instances.
• USPS First-Class Package International 7-21 day service may take longer in some instances.
• FedEx delivers to homes Tuesday-Saturday and to businesses Monday-Friday.

Position the bushing’s narrower end atop the upright base’s hub. Place a block of wood over the bushing and hammer the bushing into the hole.